fC 48 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com f toggle 9000 series power toggle switches features/benefits ? power ratings up to 10 amps ? double pole models ? locking lever options available ? w ide variety of actuator styles ? rohs compliant and compatible typical applications ? shut-off switch ? small equipment specifications contact rating: 9201 model: 6 amps @ 120 v ac or 28 v dc; 3 amps @ 250 v ac. 9221 model: 10 amps @ 125 v ac or 28 v dc; 5 amps @ 250 v ac. electrical life: 25,000 make-and-break cycles at full load. contact resistance: below 10 m typ. initial @ 2-4 v dc, 100 ma. insulation resistance: 10 9 min. dielectric strength: 2,500 vrms min. @ sea level. operating temperature: C0?oto 85?. solderability: per mil-std-202f method 208d, or eia rs-186e method 9 (1 hour steam aging). note: any models supplied with q contact material ar e rohs compliant and compatible. note: specifications and materials listed above ar e for switches with standar d options. for information on specific and custom switches, consult customer service center . materials case: diallyl phthalate (dap) (ul 94v-0). actuator: brass, chrome plated. bushing: brass or zinc, nickel plated. housing: stainless steel. switch support: brass or steel, matte-tin plated. end contacts: 9201 model: coin silver, silver plated. 9221 model: silver cadmium oxide. center contacts: copper alloy, silver plated all terminals: 9201 model: copper alloy, silver plated. 9221 model: copper alloy , matte-tin plated. terminal seal: epoxy . hardware: nut & locking ring: brass, nickel plated. lockwasher: steel, nickel plated. build-a-switch to order, simply select desired option from each category and place in the appropriate box. available options are shown and described on pages f-49 thru f-53. for additional options not shown in catalog, consult customer service center . switch function 9201 dpdt, on-on, 6 amps 9221 dpdt, on-on, 10 amps actuator s antirotation, .410" high k locking lever, .650" high k1 locking lever, .680" high l43 lever handle with cap p3 flatted, anti-rotation, .450" high t .687" high, 15/32 bushing t1 .460" high, 15/32 bushing terminations z solder lug z4 quick connect (9221 only) a v2 v ert. right angle, pc thru-hole (9201 only) c pc thru-hole bushing h3 .296" high, keyway cw splashproof h .296" high, flat contact material q silver seal e epoxy d no epoxy actuator color/finish none bright chrome 2 black kxx actuator color/finish none natural aluminum 2 black anodized aluminum bushing finish none nickel 2 black models available
fC 49 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com f toggle 9000 series power toggle switches switch function actua tor 15/32-32 uns-2a 15/32-32 uns-2a 1/4 40 uns-2a dpdt 2-1,5-4 2-3,5-6 on on on on 6 amps 10 amps 9201 9221 dp schema tic connected terminals pos. 1 pos. 2 switch function pos. 1 pos. 2 ra ting* model no. no. poles terminal nos. molded on side of case dpdt part number shown: 9201sh3zqe * see cont act material, page f-52, for complete ratings. all 9000 series models meet international dimensional and electrical requirements. 9221 model must be or der ed with z4 terminations and d seal option. actuator finish actuator s antirot ation, .410" high p3 fla tted, antirotation, .450" high t .687" high, 15/32 bushing t1 .460" high, 15/32 bushing dress nut part number: 709901201 supplied standard with p3 actuator. note: black hardware is supplied when either black actuators or bushings ar e specified. all har dware is available separately, see section n. antir otation is standar d on all actuators, pr ovides nti--ush--n?eatur e on actuator . none natural aluminumith nickel plated bushing 2 black actuator finish option code note: bushing option code not required for t & t1 actuators unless cw splashpr oof bushing or der ed. black hardware is supplied when either black actuators or bushings are specified. all har dwar e is available separately , see section n. antir otation is standar d on all actuators except t & t1, pr ovides nti--ush--n featur e on actuator. none bright chromeith nickel plated bushing 2 black actuator finish option code
fC 50 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com f toggle 9000 series power toggle switches actuator bushing 15/32-32 uns-2a 1/4-40 uns-2a 1/4-40 uns-2a locking positions 2 position lock 1/4-40 uns-2a 1/4-40 uns-2a k locking lever, .650" high, threaded h3 .296" high, threaded, keyway h .296" high, threaded, flat cw splashproof, 15/32 bushing l40 lever handle without cap l43 plastic lever handle with antirotation and cap, p/n 4812 k1 locking lever, .680" high, threaded note: t o prevent accidental actuation, toggles must be lifted before being actuated. when released, toggles again lock in place. bushing option code not r equired. overtightening mounting nut may cause actuator to bind. note: lever handle actuator l43 supplied, but not installed. for interchangeability, order l40 actuator option and order lever handles separately, see page f-53. antirotation is standard on all actuators, provides nti--ush--n?eature. inter nal actuator seal standar d. external bushing seal available separately from apm hexseal, part # mfs-60064. note: two mounting nuts, locking ring and lockwasher supplied standard with threaded bushings. black har dwar e is supplied when either black bushings or actuators ar e specified. optional mounting nut and locking ring styles and finishes available, see section n. will withstand 12 in./lbs. of tor que with no distortion. for t & t1 actuators only . finish: matte other colors available, consult customer service center . no color choice r equir ed. 2 black none no actuator color (l40 option) actuator cap color option code none nickel 2 black bushing finish option code . none na tural aluminumCith nickle plated bushing 2 black anodized aluminum actuator cap finish option code bushing finish bushing actuator finish actuator
fC 51 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com f toggle 9000 series power toggle switches bushing terminations p anel mo unting 1/4-40 uns-2a 15/32-32 uns-2a without locking ring. with standard locking ring. with small locking ring. without locking ring. with standard locking ring. pc mo unting bushing finish bushing z solder lug z4 .187" quick connect c pc thru-hole 9201 only 9221 only 9201 only note: only termination available with 9221 model. must be ordered with d seal option. mates with standard .187 nema female connector. actuator shown in pos. 3 section a-a pc mounting av2 vertical right angle, pc thru-hole 9201sh3av2qe vertical actuation dpdt note: t erminal bend radii and lead-in manufacturing option. terminal spacing greater than 3mm at all points. t erminal nos. for refer ence only 9201 only
fC 52 dimensions are shown: inches (mm) specifications and dimensions subject to change www.ck-components.com f toggle .383 (9,73) .312 (7,92) .843 (21,41) cap compatible with s actuator p ar t no. 896801000 white 896802000 black 896803000 red material: polyethylene finish: matte cap compatible with s actuator p ar t no. 706201000 white 706202000 black 706203000 red material: vinyl finish: matte l43 actuator p ar t no. 481202000 black 481203000 red material: nylon finish: matte note: additional nuts, locking rings and lockwashers available separately, see section n. other colors available, consult customer service center. 9000 series power toggle switches contact material seal a v ailable hardw are not available with 9221 model or z4 terminations. must be ordered with 9221 model and z4 termination. 6 amps @120 v ac or 28 v dc; 3 amps @ 250 v ac. 10 amps @125 v ac or 28 v dc; 5 amps @ 250 v ac. power silver or tin 2,5 tin 5 silver 1,2 silver cadmium oxide 3,4,6 9201 9221 q ratings terminal pla ting contact material model option code 1 end cont acts: coin silver, silver plated. 2 center contacts & all terminals: copper alloy, silver plated. 3 end contacts: silver cadmium oxide. 4 center contacts: copper alloy, silver plated. 5 z4 terminals only: copper alloy, matte-tin plated. 6 cadmium in electrical switch contacts is exempt fr om rohs. note: any models supplied with q contact material are rohs compliant. all 9000 series models meet international dimensional and electrical requirements. 9221 model must be or dered with z4 terminations and d seal option. * note: see t echnical data section of this catalog for rohs compliant and compatible definitions and specifications. e epoxy seal d no epoxy seal 16 [0.630] ? 2 [ 0. 0 79 ] 15/3 2-3 2, ns- 2a .464 (11 ,79) 1/4-40 u ns- 2 a nut .524 (13,3) .6 5 8 (16 ,7 ) .331 (8,4) 15/3 2-3 2 n s-2a ? .331 (8,4) .9 4 5 ( 24 ,0 ) .6 5 7 ( 16 ,7 ) 759d02000 sealing boot 703d02000 sealing boot 704d02000 sealing boot note: for use with s actuator style when combined with h3 and h bushings note: for use with t style actuator note: for use with t style actuator
|